Chemical Formulae, Equations, Calculations (Edexcel IGCSE Chemistry): Exam Questions

What numbers will balance the following equation?

_Fe (s) + _O₂ (g) → _Fe₂O₃ (g)

A company produces tin from an ore called cassiterite, which is mainly tin oxide.

What is the relative formula mass (M_r) of tin oxide, SnO₂?

[A_{*r *}of Sn= 119; O= 16 ]

What is the relative formula mass of hydrated magnesium carbonate, MgCO₃.2H₂O?

[A_{*r *}of Mg= 24; H= 1; O=16; C=12]

This question is about reactions of iron.

Iron can form iron(III) oxide with a chemical formula of Fe₂O₃.

How many atoms are shown in the formula Fe₂O₃?

Calculate the relative formula mass iron(II) hydroxide, Fe(OH)₂

(A_r: Fe = 56, O = 16, H = 1)

Calculate the percentage by mass of iron in iron(II) hydroxide, Fe(OH)₂.

Recent discoveries in the fields of Geology and Seismology have established the potential existence of a previously undiscovered iron oxide compound, FeO₂.

This iron oxide requires very high pressures and temperatures to form.

In theory, FeO₂ could be formed by the reaction of iron and oxygen, under suitable conditions, as follows.

Fe + O₂ → FeO₂

How does this reaction demonstrate the law of conservation of mass?

Draw a ring around the correct answers to complete the sentences.

There is/are $\mathrm{one}\,\mathrm{two}\,\mathrm{three}$ atom(s) of iron on both sides of the equation

There is/are $\mathrm{one}\,\mathrm{two}\,\mathrm{three}$ atom(s) of oxygen on both sides of the equation

The total number of atoms $\mathrm{increases}\,\mathrm{stays} \mathrm{the} \mathrm{same}\,\mathrm{decreases}$

This question is about the elements in Group 1.

Lithium reacts with oxygen to form solid lithium oxide.

i) Give the formula for lithium oxide.

ii) Write a balanced symbol equation for this reaction. Include state symbols in your answer.

3 g of lithium was reacted with oxygen gas.

Calculate the number of moles of lithium (A_r: Li = 7.0)

Separate: Chemistry Only

Use your answer to part (b) to do the following:

i) Calculate the number of moles of oxygen.

ii) Calculate the volume of oxygen in cm³ that reacted with 3 g of lithium.

(1 mole of gas occupies 24 000 cm³ at room temperature)

A student performed an experiment to determine the empirical formula of a Group 2 oxide, magnesium oxide.

Use the data below to show that the empirical formula is MgO.

(A_r: Mg = 24, O = 16)

A student wanted to make 15.0 g of zinc chloride. The equation for the reaction is:

ZnCO₃ + 2HCl → ZnCl₂ + CO₂ + H₂O

What mass of zinc carbonate should the student add to the hydrochloric acid to make 15.0 g of zinc chloride?

[A_{*r *}of C = 12; Zn = 65; O = 16; Cl = 35.5; H = 1]

How many moles are present in 9 kg of glucose, C₆H₁₂O₆?

[M_{*r *}of C₆H₁₂O₆ = 180 ]

The boxes show the displayed formulae of six organic compounds, P, Q, R, S, T and U.

Use the letters P, Q, R, S, T and U to answer these questions. Each letter may be used once, more than once or not at all.

i) Give the letter of the compound that is not a hydrocarbon.

ii) Give the letters of the two compounds that have the same empirical formula.

iii) Give the letter of the compound that is used to manufacture poly(propene).

Describe a test that can be used to distinguish between compounds Q and T.

test ....................................................................................................

result with compound Q ....................................................................................................

result with compound T ....................................................................................................

Compounds P, Q and R are members of the same homologous series.

Give two characteristics of a homologous series.

This is the displayed formula of an alkene, V.

i) Give the name of alkene V.

ii) Draw the displayed formula of another alkene that is an isomer of alkene V.

An organic compound has the percentage composition by mass

C = 36.36% H = 6.06% F = 57.58%

i) Show that the empirical formula of the compound is CH₂F

ii) The relative molecular mass (M_r) of the compound is 66. Determine the molecular formula of the compound.

molecular formula = ......................................................................

What is the mass of 0.25 moles of hydrated copper(II) sulfate, CuSO₄.5H₂O?

Relative formula mass (M_r): H₂O = 18 CuSO₄ = 160

Sodium hydroxide dissolves in water, forming a strongly alkaline solution.

Ammonia dissolves in water, forming a slightly less alkaline solution.

i) Identify the ion that makes the sodium hydroxide solution alkaline.

ii) What is a possible pH of ammonia solution?

When ammonia solution reacts with sulfuric acid, a neutralisation reaction occurs and ammonium sulfate forms.

i) How does the sulfuric acid act in this reaction?

ii) The diagram shows a beaker containing some ammonia solution and a few drops of phenolphthalein indicator.

Dilute sulfuric acid is added to the beaker until it is in excess.

What are the colours of the phenolphthalein indicator before and after adding excess sulfuric acid?

Ammonium sulfate is used by gardeners as a fertiliser because it contains nitrogen.

i) Explain why the chemical formula of ammonium sulfate is (NH₄)₂SO₄

Refer to the charges on the ions in your answer.

ii) Calculate the relative formula mass of ammonium sulfate, (NH₄)₂SO₄

relative formula mass = ..............................................................

iii) Calculate the mass, in grams, of nitrogen in 1.0 kg of ammonium sulfate.

mass = .............................................................. g

When zinc oxide reacts with dilute nitric acid, zinc nitrate is produced. The equation for the reaction is:

ZnO + 2HNO₃ → Zn(NO₃)₂ + H₂O

0.200 mol of nitric acid reacts with excess zinc oxide. A mass of 15.3 g of zinc nitrate is produced. Calculate the percentage yield of zinc nitrate. [M_r of zinc nitrate = 189]

The diagram shows the displayed formula of the organic compound methanol, CH₃OH

i) Determine the number of atoms in one molecule of methanol.

ii) State why methanol is not a hydrocarbon.

The atoms in methanol are held together by covalent bonds.

i) State what is meant by the term covalent bond.

ii) Draw a dot-and-cross diagram to show the bonding in a molecule of methanol. Show only the outer electrons of each atom.

Another organic compound has the percentage composition by mass

C = 38.7% H = 9.7% O = 51.6%

i) Calculate the empirical formula of this compound.

empirical formula = ..............................................................

ii) The relative molecular mass (M_r) of the compound is 62 Determine the molecular formula of the compound.

molecular formula = ........................................................

A piece of magnesium ribbon is ignited and placed in a gas jar of oxygen. The equation for the reaction is

2Mg + O₂ → 2MgO

i) Give two observations that would be made in this reaction.

1........................................................................................................2........................................................................................................

ii) State why this is an oxidation reaction.

A second piece of magnesium ribbon is ignited and placed in a gas jar of carbon dioxide. A very exothermic reaction occurs, forming magnesium oxide and carbon.

i) State what is meant by the term exothermic.

ii) Give the chemical equation for this reaction.

iii) A fire starts in a warehouse where magnesium is stored. Suggest why it would not be suitable to use a carbon dioxide fire extinguisher to put out this fire.

A student uses this apparatus to find the mass of magnesium oxide that forms when a known mass of magnesium is heated.

This is his method.

• find the mass of the crucible and lid
• place some magnesium ribbon in the crucible
• find the mass of the crucible, lid and magnesium
• heat the crucible with the lid on for a few minutes
• find the mass of the crucible, lid and magnesium oxide

Using this method, the mass of magnesium oxide formed is less than expected.

Explain two changes that the student should make to his method to obtain a mass of magnesium oxide closer to the expected mass.

Halon 1301 is a compound used in some fire extinguishers.

Halon 1301 has the percentage composition by mass of 8.05% C, 53.69% Br and 38.26% F.

Calculate the empirical formula of Halon 1301.

[A_r of C = 12; Br = 80; F = 19]

What is the maximum volume, in dm³, of chlorine gas at rtp that can be obtained from 17.6 tonnes of molten potassium chloride?

[1 tonne = 10⁶ g]

[M_{*r *}of KCl = 74.5]

[Assume that the molar volume of chlorine at rtp is 24 dm³/mol]

Calculate the concentration, in mol / dm³, of a solution produced when 6.9 g of potassium carbonate, K₂CO₃, dissolves in 200 cm³ of water.

[M_{*r *}of K₂CO₃ = 138 ]

The concentration of NaClO (aq) in a solution of bleach is found by reacting it with hydrochloric acid. The equation for the reaction is

NaClO (aq) + 2HCl (aq) → NaCl (aq) + H₂O (l) + Cl₂ (g)

An excess of dilute hydrochloric acid is added to 4.00 cm³ of bleach solution. 60.0 cm³ of chlorine gas is produced.

Explain a safety precaution that should be taken when doing this experiment.

i) Calculate the amount, in moles, of chlorine gas produced.

Assume one mole of chlorine gas occupies 24000 cm³

amount of chlorine = .............................................................. mol

ii) Determine the amount, in moles, of NaClO in 4.00 cm³ of bleach.

amount of NaClO = .............................................................. mol

iii) Calculate the concentration, in mol/dm³, of the bleach solution.

concentration = .............................................................. mol/dm³

A sample of a gaseous hydrocarbon, X, has a volume of 600 cm³ at room temperature and pressure (rtp).

Calculate the amount, in moles, of hydrocarbon X in the sample.

[molar volume of a gas = 24 000 cm³ at rtp]

amount of hydrocarbon X = .............................................................. mol

The mass of the sample of hydrocarbon X is 1.45g.

Show that the relative molecular mass (M_r) of X is 58

M_r = ..............................................................

Hydrocarbon X is an alkane.

Show that the molecular formula of X is C₄H₁₀

Give the displayed formula of the branched-chain isomer of hydrocarbon X.

The diagram shows the displayed formula of succinic acid.

What is the empirical formula for this compound?

Many different salts can be prepared from acids.

The table shows the reactants used in two salt preparations. Complete the table to show the name of the salt formed and the other product(s) in each case.

A student uses the reaction between aluminium hydroxide and dilute sulfuric acid to prepare a pure, dry sample of aluminium sulfate crystals. The equation for the reaction used to prepare this salt is:

2Al(OH)₃ + 3H₂SO₄ → Al₂(SO₄)₃ + 6H₂O

The diagram shows the steps in the student’s method.

i) State two ways to make sure that all the acid is reacted in step 2.

ii) State the purpose of filtration in step 3.

iii) In step 5, the basin is left to cool to room temperature to allow crystals of aluminium sulfate to form.

State one method of drying these crystals.

The student records this information about the reagents she uses in her preparation.

mass of aluminium hydroxide = 3.9 g

amount of sulfuric acid = 0.090 mol

Determine which reagent is in excess, making use of this information and the equation in part (b).

reagent used in excess = ..............................................................

Another student prepares 0.025 mol of aluminium sulfate. The formula of aluminium sulfate is Al₂(SO₄)₃

Calculate the mass of aluminium sulfate prepared.

mass = .............................................................. g

The equation for another reaction used to prepare a sample of a salt is:

PbO + 2HNO₃ → Pb(NO₃)₂ + H₂O

In one experiment, the amount of lead(II) oxide used was 0.75 mol and the amount of nitric acid used was 1.5 mol. At the end of the experiment, the mass of lead(II) nitrate obtained was 209 g.

Calculate the percentage yield of lead(II) nitrate in this experiment.

[M_r of lead(II) nitrate = 331]

percentage yield = .............................................................. %

Nitric acid (HNO₃) is used in the production of fertilisers.

Nitric acid is manufactured in three stages.

i) Complete the chemical equation for the reaction in stage 1.

......................NH₃ + ......................O₂ $\rightleftharpoons$ ......................NO + .......................H₂O

ii) Give the meaning of the symbol $\rightleftharpoons$

iii) State the purpose of the platinum catalyst.

Give a chemical equation for the reaction of nitrogen monoxide and oxygen in stage 2.

i) The equation for the reaction in stage 3 is

3NO₂ + H₂O → 2HNO₃ + NO

Calculate the maximum mass, in tonnes, of nitric acid that could be produced in this reaction from 11.5 tonnes of nitrogen dioxide. [1 tonne = 1.0 × 10⁶ g]

mass of nitric acid = ...................................................................... tonnes

ii) Suggest what use can be made of the nitrogen monoxide gas formed in stage 3.

When copper(II) oxide reacts with dilute nitric acid, copper(II) nitrate is produced. The equation for the reaction is

CuO + 2HNO₃ → Cu(NO₃)₂ + H₂O

0.200 mol of nitric acid reacts with excess copper(II) oxide. A mass of 15.3g of copper(II) nitrate is produced. Calculate the percentage yield of copper(II) nitrate. [M_r of copper(II) nitrate = 187.5]

Sodium hydrogencarbonate (NaHCO₃) is also known as baking soda.

Baking soda can be used to make cakes increase in size in an oven.

This is the equation for the reaction that takes place when baking soda is heated.

2NaHCO₃ (s) → Na₂CO₃ (s) + CO₂ (g) + H₂O (g)

i) What type of reaction is this?

ii) Suggest why the reaction makes the cakes increase in size.

A student uses this apparatus to investigate the reaction that takes place when sodium hydrogencarbonate is heated.

This is the student’s method.

• Weigh a crucible and record the mass
• Add some sodium hydrogencarbonate to the crucible, reweigh it and record the mass
• Heat the crucible and contents for five minutes, then allow to cool before weighing and recording the mass
• Heat the crucible and contents again for a further three minutes, then allow to cool before weighing and recording the mass

i) Give a reason why the crucible and contents are heated for a further three minutes.

ii) The student considered using a lid on the crucible in the experiment.

Suggest an advantage and a disadvantage of using a lid on the crucible.

advantage ....................................................................................................

disadvantage ....................................................................................................

The table shows some of the student’s results.

i) Calculate the mass of sodium hydrogencarbonate that the student uses.

mass = ..............................................................g

ii) Using this equation, calculate the maximum mass of sodium carbonate (Na₂CO₃) that could form in the student’s reaction.

2NaHCO₃ (s) → Na₂CO₃ (s) + CO₂ (g) + H₂O (g)

[M_r of NaHCO₃ = 84 M_r of Na₂CO₃ = 106]

maximum mass = .............................................................. g

In a second experiment, the student uses a larger mass of sodium hydrogencarbonate.

She calculates that she should obtain 4.8 g of sodium carbonate.

She actually obtains 4.2 g of sodium carbonate.

i) Calculate the percentage yield from the student’s experiment.

percentage yield = ..............................................................%

ii) Other than spillages, suggest a possible reason why the student’s actual yield is less than expected.

This question is about alkanes.

The graph shows the boiling points of several unbranched alkanes.

i) Draw a curve of best fit.

ii) Use the graph to find the boiling point of the alkane with 7 carbon atoms in its molecule.

Show on the graph how you obtain your answer.

boiling point = .............................................................. °C

iii) Explain the trend shown by the graph.

The diagram represents two isomers with the formula C₅H₁₂

Explain why these compounds are isomers.

i) An alkane contains 82.8% carbon and 17.2% hydrogen by mass. Show by calculation that the empirical formula of this alkane is C₂H₅

ii) Deduce the molecular formula of this alkane.

The equation for the complete combustion of one mole of an alkane can be represented by

alkane + ZO₂ → XCO₂ + YH₂O

Complete combustion of one mole of the alkane produces 308 g of carbon dioxide and 144 g of water.

X, Y and Z are the numbers used to balance the equation.

Calculate the values of X, Y and Z.

[M_r of CO₂ = 44, M_r of H₂O = 18]

X = ................................

Y = ................................

Z = ................................

The diagram shows the apparatus a teacher uses to determine the formula of an oxide of lead.

This is the teacher’s method.

1. Find the mass of the reduction tube
2. Add some of the lead oxide to the reduction tube
3. Find the mass of the reduction tube and lead oxide
4. Pass hydrogen gas over the lead oxide and ignite the hydrogen at the hole
5. Heat the lead oxide strongly for 10 minutes
6. Keep passing hydrogen through the reduction tube until the tube and contents are cool
7. Find the new mass of the reduction tube and its contents

i) Give a reason why hydrogen is passed through the reduction tube until the tube and contents are cool.

ii) Describe what the teacher should do next to make sure all the lead oxide has been reduced to lead.

The teacher completes the experiment and obtains these results.

• mass of reduction tube = 23.50 g
• mass of tube + lead oxide = 28.64 g
• mass of tube + lead = 28.16 g

i) Calculate the mass of lead formed.

mass of lead = .............................. g

ii) Calculate the mass of oxygen removed from the lead oxide.

mass of oxygen = .............................. g

iii) Determine the empirical formula of the lead oxide.

empirical formula of the lead oxide ..............................

The insoluble salt lead(II) chloride (PbCl₂) can be prepared by reacting a solution of lead(II) nitrate with dilute hydrochloric acid.

i) Complete the equation for the reaction by adding the state symbols.

Pb(NO₃)₂ (..........) + 2HCl (..........) → PbCl₂ (..........) + 2HNO₃ (..........)

ii) Show that the maximum mass of lead(II) chloride that can be made from 0.0370 mol of hydrochloric acid is about 5 g.

[M_r of PbCl₂ = 278]

maximum mass = .............................. g

A student uses this apparatus to heat crystals of hydrated zinc sulfate and collect the liquid produced.

i) Describe a chemical test to show that the colourless liquid contains water.

ii) Describe a physical test to show the colourless liquid is pure water.

The equation for the decomposition of hydrated zinc sulfate is

ZnSO₄·7H₂O (s) → ZnSO₄ (s) + 7H₂O (l)

The student records these masses.

• mass of boiling tube = 41.64 g
• mass of boiling tube + ZnSO₄·7H₂O = 54.46 g

Calculate the maximum volume, in cm³, of pure water that could be produced.

Give your answer to 1 decimal place.

[1.00 cm³ of pure water has a mass of 1.00 g]

[M_r of ZnSO₄·7H₂O = 287 M_r of H₂O = 18]

maximum volume of pure water = .............................. cm³

In an experiment using a different mass of ZnSO₄·7H₂O the maximum volume of pure water that could be produced is 8.5 cm³.

The student collected the pure water and calculated the percentage yield to be 20.3%.

i) Calculate the volume, in cm³, of pure water collected.

volume of pure water = .............................. cm³

ii) Explain an improvement to the apparatus that would increase the percentage yield of pure water.

This question is about the reduction of metal oxides.

Solid oxides of copper can be reduced by reacting them with methane gas.

Complete the equation for the reaction between copper(II) oxide and methane. Include state symbols.

.....CuO (.....) + .....CH₄ (.....) $\rightarrow$ .....Cu (.....) + .....CO₂ (.....) + .....H₂O (.....)

A teacher uses this apparatus to demonstrate the reaction between a different oxide of copper and methane.

The teacher heats the oxide of copper until the reaction is complete. The table shows the teacher’s results.

i) Use the teacher’s results to show that the empirical formula of this oxide of copper is Cu₂O

ii) The teacher wears safety glasses and a lab coat during the demonstration. Give one other safety precaution that she should take.

Iron forms when iron(III) oxide is heated with carbon. The equation for the reaction is:

Fe₂O₃ + 3C → 2Fe + 3CO

i) State how the equation shows that iron(III) oxide is reduced.

ii) State why carbon monoxide should not be released into the atmosphere.

iii) Calculate the maximum mass, in tonnes, of iron that can be produced when 30.0 tonnes of iron(III) oxide are reacted with an excess of carbon.

[1 tonne = 1.0 × 10⁶ g]

mass = .............................................................. tonnes

iv) A mixture of 25 000 mol of iron(III) oxide and 840 000 g of carbon is heated. Use this equation to show that the iron(III) oxide is in excess.

Fe₂O₃ + 3C → 2Fe + 3CO

A student uses the reaction between zinc and dilute sulfuric acid to prepare some zinc sulfate crystals.

i) Complete the equation for this reaction by giving the correct state symbols.

Zn (....................) + H₂SO₄ (....................) → ZnSO₄ (....................) + H₂ (....................)

ii) State what would be observed during this reaction.

The student adds excess zinc to a beaker of dilute sulfuric acid.

i) Explain why it is necessary to add excess zinc.

ii) Draw a diagram of the apparatus the student should use to remove the unreacted zinc and collect the zinc sulfate solution.

The student obtains a pure, dry sample of zinc sulfate crystals. The formula of zinc sulfate crystals is ZnSO₄.7H₂O

i) Calculate the relative molecular mass (M_r) of zinc sulfate crystals.

M_r = ..............................................................

ii) The student uses 0.0200 mol of dilute sulfuric acid in her preparation. Show that the maximum mass of zinc sulfate crystals that the student could obtain is about 6 g.

iii) The student obtains a mass of 4.28 g of zinc sulfate crystals. Calculate the percentage yield of the zinc sulfate crystals. Give your answer to three significant figures.

percentage yield = ..............................................................%

Explain the meaning of the term thermal decomposition.

The equation for the thermal decomposition of potassium hydrogencarbonate is

2KHCO₃ → K₂CO₃ + H₂O + CO₂

Calculate the maximum mass of K₂CO₃ that could be produced from the thermal decomposition of 2.50 g of KHCO₃

A student is given a pure sample of sodium carbonate crystals and is told that the formula of the crystals is Na₂CO₃.xH₂O

State what xH₂O in the formula shows about the sodium carbonate crystals.

The student uses this apparatus to find the value of x in Na₂CO₃.xH₂O

This is the student’s method.

• Find the mass of an empty crucible without a lid
• Add some sodium carbonate crystals Na₂CO₃.xH₂O to the crucible
• Find the total mass of the crucible and sodium carbonate crystals
• Heat the crucible to remove water from the crystals
• Allow the crucible and contents to cool down
• Find the mass of the cold crucible and its contents

These are the student’s results.

i) Calculate the mass of sodium carbonate left after heating and cooling.

mass of sodium carbonate = .............................................................. g

ii) Calculate the mass of H₂O lost from the sodium carbonate crystals during heating.

mass of H₂O = .............................................................. g

iii) Show that the student’s results suggest that the formula of the sodium carbonate crystals is Na₂CO₃.7H₂O

[M_r of Na₂CO₃ = 106 M_r of H₂O = 18]

The student’s teacher says that the correct formula of the sodium carbonate crystals is Na₂CO₃.10H₂O

i) The student did not make any mistakes in their measurements.

Explain what could have caused the student’s value for x to be too low.

ii) Describe how the student could improve the method to obtain a more accurate value for x.

The mineral nesquehonite is a form of hydrated magnesium carbonate. The formula, MgCO₃.xH₂O, shows that nesquehonite contains water of crystallisation. When a sample of nesquohonite is heated gently, the water of crystallisation is given off and anhydrous magnesium carbonate is left.

Six students are each given a sample of nesquehonite of mass 6.1 g. The students heat their samples for different times. The samples are then allowed to cool before being reweighed.

The table shows their results.

Plot these results on the grid provided. The last two points have been plotted for you.

Draw a straight line of best fit for the points you have plotted.

Predict the mass of sample remaining after heating for 2.5 minutes. Show on the graph how you obtain your answer.

mass after 2.5 minutes = .............................................................. g

State why the last two masses in the table are exactly the same.

A sample of nesquehonite contains 1.68 g of MgCO₃ and 1.08 g of H₂O. Calculate the value of x in the formula MgCO₃.xH₂O

[M_r of MgCO₃ = 84; M_r of H₂O = 18]

x = ..............................................................

When anhydrous magnesium carbonate is heated strongly, it decomposes. The equation for the reaction is:

MgCO₃ (s) → MgO (s) + CO₂ (g)

Calculate the volume of carbon dioxide formed in cm³, at rtp, when 4.2 g of anhydrous magnesium carbonate are completely decomposed.

[M_r of MgCO₃ = 84] [Assume that the molar volume at rtp of carbon dioxide is 24 dm³]

volume = .............................................................. cm³

A student is provided with a bottle containing a colourless solution X.

Solution X is thought to be dilute sulfuric acid of concentration 0.10 mol/dm³.

The student does some experiments on samples of solution X to try to show that it is dilute sulfuric acid.

The student adds a few drops of litmus to a sample of solution X.

The litmus turns red.

The student knows that the products of the electrolysis of dilute sulfuric acid are hydrogen and oxygen.

She carries out the electrolysis using this apparatus.

i) Suggest why the student does not use zinc electrodes in her experiment.

ii) State what is observed at both the anode and the cathode during the electrolysis.

iii) Which of these tests shows that the gas formed at the cathode is hydrogen?

Describe a test to show that solution X contains sulfate ions.

The student then does a titration to see if the concentration of the dilute sulfuric acid is 0.10 mol/dm³.

She measures 25.0 cm³ of potassium hydroxide solution into a conical flask, and then adds a few drops of indicator solution.

i) Name the piece of apparatus the student should use to measure 25.0 cm³ of the potassium hydroxide solution.

ii) The concentration of potassium hydroxide in the solution is 0.125 mol/dm³. Calculate the amount, in mol, of KOH in 25.0 cm³ of this solution.

amount = .............................................................. mol

iii) The equation for the reaction in the titration is

H₂SO₄ + 2KOH → K₂SO₄ + 2H₂O

Calculate the volume, in cm³, of 0.10 mol/dm³ sulfuric acid needed to neutralise 25.0 cm³ of the potassium hydroxide solution.

volume of sulfuric acid = .............................................................. cm³

This question is about three stages in the manufacture of sulfuric acid.

In stage 1, sulfur is burned in oxygen to form sulfur dioxide gas.

S (s) + O₂ (g) → SO₂ (g)

i) State one environmental problem caused by the release of sulfur dioxide into the atmosphere.

ii) A mass of 6.4 tonnes of sulfur is burned to produce sulfur dioxide gas. Calculate the maximum volume, in dm³, of sulfur dioxide gas that can be produced at rtp. [molar volume of sulfur dioxide gas at rtp = 24 dm³]

[1 tonne = 10⁶ g] Give your answer in standard form.

maximum volume = .............................................................. dm³

In stage 2, sulfur dioxide is reacted with oxygen to form sulfur trioxide gas.

2SO₂ (g) + O₂ (g) $\rightleftharpoons$ 2SO₃ (g)

The yield of sulfur trioxide is approximately 98%.

i) A catalyst is used in this reaction. Explain how a catalyst increases the rate of a reaction.

ii) The temperature is kept constant.

Give a reason why increasing the pressure would increase the yield of sulfur trioxide.

iii) Suggest why it is not necessary to increase the pressure in stage 2.

In stage 3, the sulfur trioxide is reacted with concentrated sulfuric acid to form a liquid called oleum, H₂S₂O₇

The oleum is then added to water to form concentrated sulfuric acid.

Complete the chemical equations for these two reactions.

............................ + ............................ → H₂S₂O₇

H₂S₂O₇ + ............................ → ...........................

Sulfuric acid reacts with ammonia to form ammonium sulfate, (NH₄)₂SO₄

Calculate the percentage by mass of nitrogen in ammonium sulfate.

[M_r of (NH₄)₂SO₄ = 132]

percentage = .............................................................. %

A student uses this apparatus to determine the formula of magnesium oxide.

This is the student's method:

• weigh the crucible and its lid.
• coil about 20cm of magnesium ribbon, place it in the crucible and reweigh
• heat the crucible strongly with the Bunsen burner, lifting the lid from time to time
• allow the crucible to cool and reweigh
• repeat the heating and cooling until a constant weight is obtained

The table shows the student's results:

i) Calculate the mass of magnesium used in the experiment.

Mass of Mg:

ii) Calculate the mass of magnesium oxide formed.

Mass of magnesium oxide:

iii) Determine the empirical formula of magnesium oxide using these results.

Formula of magnesium oxide:

Explain why the student:

i) Lifted the lid from time to time during the experiment.

ii) Repeated the experiment to obtain a constant weight.

Titanium(IV) oxide can be converted to titanium(IV) chloride by heating with carbon and chlorine.

The equation for the reaction is:

TiO₂ + 2C + Cl₂ $\rightarrow$TiCl₄ + 2CO

i) State, with a reason, whether this is a redox reaction.

ii) Calculate the relative formula mass (M_r) of titanium(IV) oxide and titanium(IV) chloride.

(A_r Ti = 48)

iii) Determine the maximum mass of titanium(IV) chloride that can be made from 200 tonnes of titanium(IV) oxide.

[1 tonne = 1000 kg]

iv) A chemical engineer calculates that a furnace should produce 380 tonnes of titanium(IV) chloride from 160 tonnes of titanium(IV) oxide.

The furnace actually produces 293 tonnes of titanium(IV) chloride.

Calculate the percentage yield of titanium(IV) chloride.

Titanium(IV) chloride is a colourless liquid.

i) State the type of structure present in titanium chloride.

ii) Explain why the structure of titanium(IV) chloride is anomalous.